Local manufacturing capabilities in Poughkeepsie, NYOur shop · Videos · About · Contact · Call 845-402-6318

Home / Products / Ceramic / Acid & caustic recovery

Ceramic MF/UF · pH 0–14 material

Acid and caustic streams polymer can’t touch.

Pickling acid, metal-finishing rinse, spent caustic and acidic process slurries all sit outside the pH 2–11 window of most polymer membranes. Silicon carbide is stable from pH 0 to 14. Ceramic filtration takes out the particles, oil and silica, so the acid or caustic can go back to the bath or on to a recovery step.

Send us the chemistry. We will tell you which ceramic and which seals.

Silicon carbide ceramic membranes for acid and caustic streams

What plants tell us

The problems that bring acid & caustic recovery plants to ceramic.

“The pH is off the chart.”

PVDF UF operates at pH 2–11, PAN at 2–10 or 3–10. Pickling acid and spent caustic are outside both.

“We keep buying fresh acid.”

Ceramic MF removes particles, oil and silica from pickling acid. Nanofiltration downstream can pull dissolved metals so the acid goes back to the bath.

“Spent caustic goes to neutralization.”

Published ceramic systems recycle over 95% of spent caustic at pH 10–13 and above 122 °F (50 °C).

“Strong alkali destroys our membranes.”

PVDF dehydrofluorinates and turns brittle at pH 12 and above.

“Our acidic slurry won’t settle.”

Fine particles in acid leach and process slurries stay suspended. Cross-flow ceramic separates them without filter aid.

Why ceramic fits

Built for this stream.

  • SiC material is stable across pH 0–14. Housings, seals and gaskets are matched to the acid or caustic and quoted per stream.
  • Hot operation possible in tubular stainless housings. 300 °F (about 150 °C) is not a problem for most ceramic and stainless steel builds.
  • Real backwash plus acid and caustic chemical cleaning.
  • Pairs with NF, diffusion dialysis or evaporation when dissolved metals or concentration must change.
  • Abrasion-resistant against scale, oxide and grit.

Typical stream conditions

What we size against.

ParameterTypical in this industryWhat it means for the membrane
Pickling acid (HCl, H₂SO₄)Very low pH, iron and metals, oil, silicaCeramic MF for solids and oil; NF for dissolved metals
Metal-finishing rinseLow or high pH, metals, oils, brightenersCeramic removes solids and oil ahead of recovery or reuse
Spent causticpH 10–13.5, often above 122 °F (50 °C)Ceramic recovers the caustic; strength adjusted after
Acidic slurriesFine particles, catalyst, productCross-flow ceramic for solid–liquid separation

Ranges widely documented in industry literature. Your stream sets the design.

Projects like these

Where ceramic is already running on acid & caustic recovery streams.

Typical case types from ceramic membrane installations worldwide. Names, sites and sizes are withheld, and no single result carries over to your stream.

Acidic solid–liquid separation

Fine solids separated from strong-acid process streams with SiC.

Catalyst recovery

Nanometer catalyst retained and returned to the reactor while product passes.

Spent caustic recycle

Caustic cleaned and returned to cleaning circuits.

Acid bath maintenance

Particles and oil removed so pickling and etch baths last longer.

SiC or alumina

Which ceramic for this job.

SiC for the most extreme pH and oxidants. Alumina is resistant to most acids and alkalis and offers a tighter cut-off, but confirm the chemistry for strong hot caustic and HF. Seal, gasket and housing materials set the real limits and are quoted per stream.

Ceramic flux depends on the application. As a general range, expect about 6–29 GFD (10–50 LMH) for non-pressurized (submerged) systems, and up to 100 GFD (170 LMH) for pressurized systems.

Warranty against defects in materials and workmanship. For industrial applications, membrane life depends on the service duty, so we run a pilot test to establish expected system life.

Honest selection

Ceramic removes particles and oil. It does not remove dissolved metals or change acid strength. Pair it with NF, diffusion dialysis, ion exchange or evaporation for that. For dilute rinse water near neutral, polymer may be enough.

What to send

Feed first.

  • Stream, flow, and acid or caustic type and strength
  • Temperature (°F), metals, oil, solids, silica
  • Goal: back to bath, to recovery, or to discharge
  • Materials already in contact: tanks, piping, seals
  • Any oxidants, fluoride or solvents

Lab or pilot testing on a sample is available before you commit.

Quick quote · 1 minute

Send us the stream.

Only your name and email are required. We reply from tom@zyramic.com, usually within one business day. Or call 845-402-6318.

Call 845-402-6318

Built and backed in the USA.

Ceramic elements come from certified sources, and the quotation documents their origin. Zyramic supplies the modules, and frames and skids are assembled in our Poughkeepsie, NY shop.

We presently have a manufacturing facility in Poughkeepsie, New York, and the ability to ship from Europe and Asia.

On a federally funded job? Tell us your domestic-content requirements, including Build America, Buy America (BABA), and we'll review what we can document.

Zyramic, Inc.
14 Tucker Dr, Suite 4
Poughkeepsie, NY 12603
845-402-6318 · tom@zyramic.com

Related: CIP caustic recovery in food plants · Degreasing & coolant · Hydrometallurgy · All harsh industrial streams · Ceramic modules

Ceramic data sheet (PDF) · Tubular class datasheet (PDF)

Call 845-402-6318Get a quote