Local manufacturing capabilities in Poughkeepsie, NYOur shop · Videos · About · Contact · Call 845-402-6318

Home / Products / Ceramic / Mine water

Ceramic MF · mining discharge

Mine water is abrasive, acidic and full of metals. Ceramic is built for that.

Acid mine drainage and mine dewatering water carry fine grit, iron and other metals, and low pH. After lime or caustic precipitation, the metal hydroxides have to come out. Clarifiers lose fines and polymer fibers wear. Ceramic microfiltration gives a hard barrier that can be backwashed and acid-cleaned.

Send us the water analysis. We will tell you where ceramic fits in your train.

Silicon carbide flat-sheet ceramic membranes for mine water

What plants tell us

The problems that bring mine water plants to ceramic.

“Fines carry over the clarifier.”

Fine hydroxide floc and grit settle slowly and slip into the discharge. Ceramic MF is a positive barrier for particles after precipitation.

“Grit wears out membranes.”

Ceramics resist abrasive mine particles and harsh chemistry better than polymer.

“The water is acidic and the cleaning is too.”

PVDF UF runs at pH 2–11. Raw AMD and acid cleaning sit outside that. SiC is stable from pH 0 to 14.

“Our limits keep tightening.”

Discharge limits on metals and TSS force a polishing step after conventional treatment.

Why ceramic fits

Built for this stream.

  • Rigid ceramic resists abrasion from mine fines.
  • Backwash plus acid cleaning removes hydroxide and scale fouling.
  • Open SiC sheet spacing up to 1.42 in (36 mm) for high-solids tanks.
  • Pairs with lime or caustic precipitation, then MF, then RO if salts must come down.
  • Can thicken the sludge stream as well as polish the water.

Typical stream conditions

What we size against.

ParameterTypical in this industryWhat it means for the membrane
pHOften low in raw AMD; neutral to alkaline after precipitationCeramic stable at both
MetalsIron, manganese, aluminum, zinc, copper and othersPrecipitate first; MF does not remove dissolved metals
SolidsFine grit and hydroxide flocBackwashable ceramic; SiC sheet spacing set against solids
TemperatureUsually ambientSiC flat sheet in a tank fits; housing rated 41–113 °F (5–45 °C)

Ranges widely documented in industry literature. Your stream sets the design.

Projects like these

Where ceramic is already running on mine water streams.

Typical case types from ceramic membrane installations worldwide. Names, sites and sizes are withheld, and no single result carries over to your stream.

Mine water treatment

SiC used on mine water to remove fines and precipitated metals.

Acidic solid–liquid separation

Fine solids separated from acidic streams with ceramic.

High-solids submerged duty

Wide-spaced SiC sheets in open tanks where sludge is heavy.

SiC or alumina

Which ceramic for this job.

SiC flat sheet submerged in a tank is the usual fit for ambient mine water. The standard SiC flat-sheet module housing is rated 41–113 °F (5–45 °C). Tubular for pressurized or hot process water in mineral processing.

Ceramic flux depends on the application. As a general range, expect about 6–29 GFD (10–50 LMH) for non-pressurized (submerged) systems, and up to 100 GFD (170 LMH) for pressurized systems.

Warranty against defects in materials and workmanship. For industrial applications, membrane life depends on the service duty, so we run a pilot test to establish expected system life.

Honest selection

Microfiltration only removes what is a particle. Dissolved metals must be precipitated first, and sulfate and TDS need RO or another step. If your clarifier already meets the TSS limit, ceramic may not be needed.

What to send

Feed first.

  • Flow, average and peak (including storm)
  • pH, iron, manganese, aluminum, other metals, sulfate
  • TSS and current precipitation chemistry
  • Discharge limits
  • Site power and access

Lab or pilot testing on a sample is available before you commit.

Quick quote · 1 minute

Send us the stream.

Only your name and email are required. We reply from tom@zyramic.com, usually within one business day. Or call 845-402-6318.

Call 845-402-6318

Built and backed in the USA.

Ceramic elements come from certified sources, and the quotation documents their origin. Zyramic supplies the modules, and frames and skids are assembled in our Poughkeepsie, NY shop.

We presently have a manufacturing facility in Poughkeepsie, New York, and the ability to ship from Europe and Asia.

On a federally funded job? Tell us your domestic-content requirements, including Build America, Buy America (BABA), and we'll review what we can document.

Zyramic, Inc.
14 Tucker Dr, Suite 4
Poughkeepsie, NY 12603
845-402-6318 · tom@zyramic.com

Related: Acid streams · Hydrometallurgy · All harsh industrial streams · Ceramic modules

Ceramic data sheet (PDF) · Tubular class datasheet (PDF)

Call 845-402-6318Get a quote