Local manufacturing capabilities in Poughkeepsie, NYOur shop · Videos · About · Contact · Call 845-402-6318

Home / Products / Ceramic / Hot oily emulsions

Ceramic MF/UF · hot oil-in-water emulsions

Hot, oily water? Recover the oil, the water and the heat.

Edible-oil refining, palm-oil milling, rendering and hot process rinses produce emulsions near boiling. Polymer UF has to wait until the stream cools to about 104 °F (40 °C), and the oil fouls it anyway. Ceramic can filter while the water is still hot. Oil is concentrated for sale or reuse, and hot permeate goes back to the process.

Send us the temperature and the oil content. We will tell you what ceramic can recover.

Silicon carbide tubular ceramic membranes for hot oily emulsions

What plants tell us

The problems that bring hot oily emulsions plants to ceramic.

“We have to cool it before we can filter it.”

PVDF UF is typically rated to 104 °F (40 °C) and PAN to 113–131 °F (45–55 °C). Palm-oil mill effluent is discharged at 176–194 °F (80–90 °C). Cooling it costs money and throws the heat away.

“Flux never comes back after cleaning.”

Polymer membranes degrade above about 122 °F (50 °C), and oil causes irreversible fouling. Ceramic can be cleaned with aggressive chemicals at higher temperature.

“We’re sending oil to the drain.”

In published tests on palm-oil effluent, alumina UF concentrated the oil further and recovered more water than PVDF (60.5% vs 46.6%), with 99.8% COD rejection.

“The oil load is far above what our membranes allow.”

Submerged polymer UF feed limits are about 100–300 mg/L oil and grease. Hot food-oil emulsions run well above that.

Why ceramic fits

Built for this stream.

  • Runs hot. Alumina ran stably above 194 °F (90 °C) in published tests. 300 °F (about 150 °C) is not a problem for most ceramic and stainless steel builds.
  • SiC has shown lower irreversible fouling than alumina on oil-in-water emulsions.
  • Oil is retained and concentrated for phase separation, sale or reuse.
  • Hot permeate can return to the process. RO elements are typically limited to 113 °F (45 °C), so skipping RO keeps the heat.
  • Long life: ceramic is commonly quoted at about 20 years vs 7–10 for polymer, at 5–10× the capital cost.

Typical stream conditions

What we size against.

ParameterTypical in this industryWhat it means for the membrane
Temperature176–194 °F (80–90 °C) for palm-oil effluent; other hot rinses varyTubular ceramic in stainless; flat sheet only to 113 °F (45 °C)
OilFree and emulsified, often far above 300 mg/LCross-flow concentrates oil; SiC sheds it best
CODVery high; 99.8% rejection in published testsPermeate quality set by pore and stream
Solids and fiberFruit fiber, protein, cell debrisCoarse screen and decant ahead

Ranges widely documented in industry literature. Your stream sets the design.

Projects like these

Where ceramic is already running on hot oily emulsions streams.

Typical case types from ceramic membrane installations worldwide. Names, sites and sizes are withheld, and no single result carries over to your stream.

Palm-oil recovery

Valuable oil recycled from hot palm-oil process water with ceramic.

Edible-oil emulsions

Hot emulsions separated at temperature, then oil recovered and water reused.

Oil–water separation

SiC used for free and emulsified oil across food and chemical plants.

Zero-discharge layouts

Ceramic used to recover nearly all solids and oil where the plant aims for zero liquid discharge.

SiC or alumina

Which ceramic for this job.

Tubular SiC or alumina in stainless steel for anything above 113 °F (45 °C). SiC for the oiliest streams, alumina where a tighter cut-off is wanted. The standard SiC flat-sheet module housing is rated 41–113 °F (5–45 °C).

Ceramic flux depends on the application. As a general range, expect about 6–29 GFD (10–50 LMH) for non-pressurized (submerged) systems, and up to 100 GFD (170 LMH) for pressurized systems.

Warranty against defects in materials and workmanship. For industrial applications, membrane life depends on the service duty, so we run a pilot test to establish expected system life.

Honest selection

Ceramic costs more up front, often 5–10× polymer. It pays when it is the only membrane that survives the heat, or when the recovered oil and heat cover the difference. If the stream is already cool, ask whether polymer or SiC flat sheet will do.

What to send

Feed first.

  • Flow, temperature (°F), pH
  • Oil and grease, free vs emulsified
  • TSS, fiber, protein
  • What you want back: oil, water, heat
  • Current treatment and haul-off cost

Lab or pilot testing on a sample is available before you commit.

Quick quote · 1 minute

Send us the stream.

Only your name and email are required. We reply from tom@zyramic.com, usually within one business day. Or call 845-402-6318.

Call 845-402-6318

Built and backed in the USA.

Ceramic elements come from certified sources, and the quotation documents their origin. Zyramic supplies the modules, and frames and skids are assembled in our Poughkeepsie, NY shop.

We presently have a manufacturing facility in Poughkeepsie, New York, and the ability to ship from Europe and Asia.

On a federally funded job? Tell us your domestic-content requirements, including Build America, Buy America (BABA), and we'll review what we can document.

Zyramic, Inc.
14 Tucker Dr, Suite 4
Poughkeepsie, NY 12603
845-402-6318 · tom@zyramic.com

Related: Food & beverage · Metalworking coolant & oily water · All harsh industrial streams · Ceramic modules

Ceramic data sheet (PDF) · Tubular class datasheet (PDF)

Call 845-402-6318Get a quote