Home / Products / Ceramic / Brine & chlor-alkali
Ceramic MF/UF · brine refining
Cleaner brine, without precoat.
Chlor-alkali and salt plants filter brine to protect ion-exchange resin and cells. Precoat and sand filters use filter aid, make waste and let fines slip. Ceramic cross-flow filtration removes magnesium hydroxide, calcium carbonate, fibers and fines directly, in a concentration of salt that is hard on most polymers.
Send us your brine analysis. We will size ceramic against it.

What plants tell us
The problems that bring brine & chlor-alkali plants to ceramic.
“Filter aid is a running cost and a waste stream.”
Precoat filters consume filter aid and produce spent cake. Ceramic cross-flow replaces precoat or sand filtration in primary brine.
“Fines get through and foul the resin.”
Solids that slip past sand or precoat load the chelating resin and cells. Ceramic removes Mg(OH)₂, CaCO₃, fibers and fines ahead of the resin.
“Brine chemistry is hard on everything.”
Hot, near-saturated brine with pH swings during treatment. PVDF is rated to pH 11 and degrades in strong alkali. Ceramic is unaffected by the salt and the pH.
“We run a biological step on salty water.”
Brine-side MBR on high-salt coal-chemical wastewater is an established ceramic application. Ceramic is unaffected by the salt and takes strong cleaning.
Why ceramic fits
Built for this stream.
- SiC and alumina are unaffected by salt concentration.
- Backwash and acid cleaning remove Mg(OH)₂ and CaCO₃ deposits.
- No filter aid to buy or dispose of.
- Steady solids cut-off protects downstream resin and cells.
- Hot brine in tubular stainless housings. 300 °F (about 150 °C) is not a problem for most ceramic and stainless steel builds.
Typical stream conditions
What we size against.
| Parameter | Typical in this industry | What it means for the membrane |
|---|---|---|
| Salt | Near-saturated NaCl or KCl brine | No effect on ceramic; seals and metals chosen for chloride |
| Precipitated solids | Mg(OH)₂, CaCO₃ after chemical treatment | Ceramic MF removes them |
| pH and temperature | Alkaline during precipitation, often warm | Ceramic stable; check housing metallurgy |
| Downstream | Chelating ion exchange still removes residual Ca and Mg | Ceramic protects it, it does not replace it |
Ranges widely documented in industry literature. Your stream sets the design.
Projects like these
Where ceramic is already running on brine & chlor-alkali streams.
Typical case types from ceramic membrane installations worldwide. Names, sites and sizes are withheld, and no single result carries over to your stream.
Chlor-alkali brine refining
Primary brine filtered with ceramic ahead of ion exchange.
Coal-chemical brine MBR
Ceramic MBR on high-salt coal-chemical wastewater.
High-salt industrial streams
Ceramic filtration on salt brines in chemical plants.
SiC or alumina
Which ceramic for this job.
SiC flat sheet or tubular for primary brine and brine-side MBR. Chloride-resistant housings and seals are quoted per project. The standard SiC flat-sheet module housing is rated 41–113 °F (5–45 °C).
Ceramic flux depends on the application. As a general range, expect about 6–29 GFD (10–50 LMH) for non-pressurized (submerged) systems, and up to 100 GFD (170 LMH) for pressurized systems.
Warranty against defects in materials and workmanship. For industrial applications, membrane life depends on the service duty, so we run a pilot test to establish expected system life.
Honest selection
Ceramic filtration removes particles. It does not remove dissolved calcium and magnesium; ion exchange still does that. Chloride is hard on stainless steel, so housing materials matter as much as the membrane.
What to send
Feed first.
- Brine type and concentration, flow, temperature (°F)
- Suspended solids and what precipitates them
- Current filtration (precoat, sand, other) and its cost
- Downstream: ion exchange, cells, evaporator
- Materials constraints
Lab or pilot testing on a sample is available before you commit.
Built and backed in the USA.
Ceramic elements come from certified sources, and the quotation documents their origin. Zyramic supplies the modules, and frames and skids are assembled in our Poughkeepsie, NY shop.
We presently have a manufacturing facility in Poughkeepsie, New York, and the ability to ship from Europe and Asia.
On a federally funded job? Tell us your domestic-content requirements, including Build America, Buy America (BABA), and we'll review what we can document.
Zyramic, Inc.
14 Tucker Dr, Suite 4
Poughkeepsie, NY 12603
845-402-6318 · tom@zyramic.com
Related: Acid & caustic streams · Lithium brine · All harsh industrial streams · Ceramic modules
