Local manufacturing capabilities in Poughkeepsie, NYOur shop · Videos · About · Contact · Call 845-402-6318

Home / Products / Ceramic / Pulp & paper

Ceramic MF/UF · pulp, paper & board

Hot, fibrous white water, clarified for reuse.

As a mill closes its water loop, white water gets hotter and carries more fines, fiber fragments, colloids and dissolved organics. That is the temperature range where polymer UF starts to fail. Ceramic cross-flow filtration clarifies white water for shower and process reuse without cooling it.

Send us a white-water analysis. We will tell you where ceramic fits.

Silicon carbide tubular ceramic membranes for paper mill white water

What plants tell us

The problems that bring pulp & paper plants to ceramic.

“Closing the loop made the water hot.”

Closed white-water loops have been studied at 122 °F (50 °C). PVDF UF is typically rated to 104 °F (40 °C) and PAN to 113–131 °F (45–55 °C).

“Fines and fiber plug our filters.”

Fines, fiber fragments and fillers foul fiber-bundle membranes. Cross-flow ceramic filters with automatic backwash and chemical cleaning have been applied to white water.

“Deposits and pitch keep coming back.”

UF removes suspended solids and fatty acids well, which helps with deposits. Dissolved COD and TDS removal is moderate.

“Fresh water and effluent costs keep rising.”

Every gallon of clarified white water reused on showers or dilution is a gallon not drawn and not treated.

Why ceramic fits

Built for this stream.

  • Runs at white-water temperature. 300 °F (about 150 °C) is not a problem for most ceramic and stainless steel builds.
  • Backwash plus chemical cleaning clears fines and pitch.
  • Abrasion-resistant against fillers and coating pigments.
  • Clear permeate for high-pressure showers and seal water.
  • Pairs with biological treatment where dissolved COD must come down.

Typical stream conditions

What we size against.

ParameterTypical in this industryWhat it means for the membrane
TemperatureAbout 122 °F (50 °C) and up in closed loopsTubular ceramic; flat sheet only to 113 °F (45 °C)
SolidsFines, fiber fragments, fillers, pigmentsBackwashable cross-flow ceramic
OrganicsFatty and resin acids, dissolved CODUF removes the colloidal part; dissolved COD partly passes
Reuse targetsShowers, seal water, dilutionParticle-free permeate

Ranges widely documented in industry literature. Your stream sets the design.

Projects like these

Where ceramic is already running on pulp & paper streams.

Typical case types from ceramic membrane installations worldwide. Names, sites and sizes are withheld, and no single result carries over to your stream.

Papermaking process water

Ceramic used to treat paper-mill process water for reuse.

White-water polishing

Cross-flow ceramic polishing filters on white water.

High-solids submerged duty

Wide-spaced SiC sheets for fibrous, high-solids water.

SiC or alumina

Which ceramic for this job.

Tubular SiC or alumina for hot white water. SiC flat sheet where the stream has cooled, for example effluent polishing. The standard SiC flat-sheet module housing is rated 41–113 °F (5–45 °C).

Ceramic flux depends on the application. As a general range, expect about 6–29 GFD (10–50 LMH) for non-pressurized (submerged) systems, and up to 100 GFD (170 LMH) for pressurized systems.

Warranty against defects in materials and workmanship. For industrial applications, membrane life depends on the service duty, so we run a pilot test to establish expected system life.

Honest selection

UF will not remove much dissolved COD or salt, so a fully closed loop still needs biology or other steps. For cooled mill effluent, an MBR may be the better buy.

What to send

Feed first.

  • Flow and temperature (°F)
  • TSS, consistency, fillers, COD, conductivity
  • Reuse point and quality target
  • Current save-all or filter performance
  • Grade and furnish

Lab or pilot testing on a sample is available before you commit.

Quick quote · 1 minute

Send us the stream.

Only your name and email are required. We reply from tom@zyramic.com, usually within one business day. Or call 845-402-6318.

Call 845-402-6318

Built and backed in the USA.

Ceramic elements come from certified sources, and the quotation documents their origin. Zyramic supplies the modules, and frames and skids are assembled in our Poughkeepsie, NY shop.

We presently have a manufacturing facility in Poughkeepsie, New York, and the ability to ship from Europe and Asia.

On a federally funded job? Tell us your domestic-content requirements, including Build America, Buy America (BABA), and we'll review what we can document.

Zyramic, Inc.
14 Tucker Dr, Suite 4
Poughkeepsie, NY 12603
845-402-6318 · tom@zyramic.com

Related: All harsh industrial streams · UF for industrial water reuse · Ceramic modules

Ceramic data sheet (PDF) · Tubular class datasheet (PDF)

Call 845-402-6318Get a quote